Deprecated: Function strftime() is deprecated in /home/internet/www.pa7n.nl/pa7n-utils.php on line 107

New QRP SDR transceiver!

A few weeks ago I ordered a new transceiver. The mcHF. It's a SDR QRP HF transceiver. It's a kit. There are two kinds of kits. One with all pcb's and components and one with the SMD components already placed on the pcb.

I ordered the kit with all SMD components already placed on the PCB. After a few hours of building the transceiver was ready for the smoke test! It worked. No smoke. There was only one push button that caused the transceiver to power off. After some searching I found a short between two pins of the mpu.

The mcHF worked perfectly after fixing the short. There was just one thing that concerns me. In receive mode the current was 410 mA at 13.8V. The linear regulators where getting very hot. I mounted them on a heatsink but they where still getting very hot. Most of the current is draw at the 5V regulator that is in serie with the 8V regulator. The current at the 8V line was only about 16mA. So if you multiply 0,410 x (13.8-5) is about 3,6 Watt of heat disipation. The transceiver itself uses only about 2 Watt (0,410 x 5 V) .

So why not replace the 5V linear regulator with a switched regulator? Noise?!? I bought a drop-in switched regulator (Wurth 5V/1A Farnell: 173010578) and connected it with a few wires to the mcHF board. It worked. The current dropped to 163 mA. (That is less then a KX3!) After connecting a dummy load there was no increase in noise. So that looks good. I still have to build it in the mcHF enclosure and find out if there is still no increase in noise. But so far so good. The mcHF is now a really cool transceiver!

Note:
It is not a simple modification as a simple drop-in replacement. The thing is you want the input of the switched regulator connect to the DC power input (12-13.8V) of the mcHF not to the 8V regulator. If you do that the 8V regulator still heats up and the improvement is minimal. But if you connect to the DC input there is no way to turn the mcHF off. I think I need something with a pnp transistor to switch the 5V rail off when the 8V rail is off.

Update 28-06-2017:
Today I put the switching regulator inside the mcHF and the noise level increased to about S1. But worse I found some spurious here and there. With stronger ones every 300kHz (the switching frequency). So I think I have to say: Nice try but it didn't work! :-(
So back to the linear regulators. At least I have something to warm my hands on a cold SOTA summit.

More info about this great open source project:
http://www.m0nka.co.uk/

Comments

Deprecated: Function strftime() is deprecated in /home/internet/www.pa7n.nl/pa7n-utils.php on line 107

SDR Cube

Deze maand (december 2010) is er een nieuwe SDR transceiver kit beschikbaar. De "SDR Cube". Het is een transceiver gebaseerd op de bekende Softrock SDR.

Maar in tegenstelling tot de Softrock SDR, die een geluidskaart en computer nodig heeft, is de SDR Cube een stand-alone transceiver.
Intern heeft deze een audio codec (A/D en D/A converter) en een DSP processor. En dat allemaal in een heel klein kastje. De SDR Cube heeft zelfs een grafisch display met een bandscope. De software is open-source dus zelf experimenteren met de DSP software kan ook. De basiskit kost 199 dollar.

Het lijkt mij een ontzettend leuk project. Met nieuwe technieken en een SDR aanpak die ik bij de grote merken nog niet ben tegengekomen. Leuk dat het weer de zendamateurs zijn die met nieuwe technieken aan pionieren zijn.

Meer info:
www.sdr-cube.com

Comments